Is My Pressure Tank Bad The 4 Signs to Look For

Are you looking at your pressure tank and wondering whether or not it’s bad? If you’re experiencing symptoms such as headaches, dizziness, nausea, or blurred vision, then you may want to get it checked out.

You may wonder why your pressure tank is giving you trouble. There are several reasons why your pressure tank might be malfunctioning. One reason could be because of a leaky valve. Another reason could be due to a clogged filter.

Here are some signs that your pressure tank is malfunctioning.

How Do I know if I Need a New Pressure Tank?

If you have been diagnosed with glaucoma, then you should know that there are different types of eye drops available for treatment.

Your doctor will prescribe the right type of drops depending on your condition and other factors. You can also buy an over-the-counter (OTC) prescription drug called “pressure control drops” from any pharmacy. These OTC drugs come in various strengths and are designed to help reduce the amount of pressure inside your eyes.

However, most people who use these OTC medications do not experience relief. This is because they don’t take them correctly. They either forget to take their medication or they fail to follow the instructions properly. In addition, many patients complain about side effects associated with these medications.

​

How Well do Pressure Tanks Work?

A pressure tank works by using a pump to push fluid into your eye. Your eye contains two chambers: the anterior chamber and the posterior chamber.

The anterior chamber is filled with water while the posterior chamber is empty. When you blink, the muscles in your eyelids squeeze shut causing a vacuum effect. This creates negative pressure which draws fluid out of the front chamber through the drainage tube.

The fluid travels down the tube and enters the back chamber where it gets stored until you blink again. Once you blink, the negative pressure pulls more fluid out of the back chamber and pushes it into the front chamber.

The pressure inside your eye increases when you open your eyes. As a result, the fluid inside the eye moves towards the front chamber. This causes the fluid level to rise inside the front chamber.

Signs Your Pressure Tank is Bad

There are four main things that you need to look for when checking your pressure tank. These include:

1. Leaking Valve

2. Clogged Filter

3. Low Fluid Level

4. High Eye Pressure

Leaky Valve

Leaks occur when the valve connecting the tubing to the eye becomes damaged. A leaking valve allows air to enter the system. This results in low pressure inside the eye.

When you check your pressure tank, make sure that it has no leaks. Also, make sure that the valves are tightly closed.

Clogged Filter

When you first start using your new pressure tank, you may notice that the bottle is full but your eye feels dry. This is usually caused by a clogged filter. If this happens, gently shake the bottle upside down. Make sure that all the liquid drains out of the bottom of the bottle.

After shaking the bottle, remove the cap and clean the filter. Make sure that the filter is completely clear before putting the cap back on.

Low Fluid Level

If you find that your eye feels dry even after taking your prescribed dose of drops, then you might be experiencing low fluid levels. Check your fluid level by following the steps below:

• Turn off the power switch at the base of the bottle.

• Remove the cap.

• Hold the bottle upright and tilt it so that the fluid comes out of the top.

• Place the bottle on a flat surface.

• Wait for 5 minutes.

• Replace the cap.

High Eye Pressure

If you have high eye pressure, then you should see your ophthalmologist as soon as possible. He/she will prescribe you the correct type of drops based on your condition.

How does A Typical Well Pump System work?

Most well pumps work in the same way as an ordinary pressure tank. They consist of a reservoir, a tube, a valve and a hand-held pump.

The reservoir holds the fluid used to fill the tubes. It also stores any excess fluid that cannot fit into the tubes.

• The tube connects the reservoir to the eye.
• The valve controls how much fluid flows from the reservoir to the eye via the tube.
• The pump helps move the fluid through the tube.
• The reservoir can hold up to 500 ml (17 fl oz) of fluid.
• The tube can hold up to 1 litre (34 fl oz).
• The valve can control the flow rate of the fluid from 0ml per minute to 250 ml per minute.
• The pump can handle fluids with viscosities ranging from 10 cP to 100000 cP.

Well Pumps vs. Pressure Tanks

Pressure tanks provide continuous delivery of medication while well pumps deliver intermittent doses. However, both types of devices offer similar benefits.

Continuous Delivery

A typical pressure tank provides continuous delivery of medication because there is always some amount of fluid inside the reservoir. This means that the patient does not have to take multiple doses throughout the day.

Intermittent Dosing

With a well pump, the dosage of medicine delivered depends on the speed at which the pump pushes the fluid through the tube towards the eye. When the pump stops pushing the fluid, the fluid remains inside the tube until the next time the pump starts working again.

This allows patients to get their required dosage without having to wait for the entire dose to pass through the tube.

Safety Features

Both pressure tanks and well pumps come with safety features such as alarms, shutoff switches, and leak detection systems. This help protects users against accidents.

​

Conclusion

There are many different types of eye care products available today. To choose the right one, make sure that you know what each product is designed to do.

For example, if you want to treat glaucoma, then you need to use a device that has anti-glaucoma properties. You don’t want to buy a product that just treats the symptoms but doesn’t cure the underlying cause.